12mm Double Handle Electric Router Electric Hand Wood Router

September 24 09:02:44, 2018

Model NO.: 1324-18-12E
Condition: New
Color: Red
Motor: Copper Wire Motor
Application: Carving and Trimming
Plug: BS, VDE, etc
Cutting Range: Max 50mm
Plunge Depth: 65mm
Rated Voltagecarving Wood: 220V
Power(W): 1880W
Safety: Double Insulation
Speed: 9000-22000r/Min
Frequency: 50Hz
Trademark: ZLRC
Transport Package: Standard Packing
Specification: 5.7KG
Origin: China
HS Code: 8465920000

12MM Double handle Electric Router Electric Hand Wood Router

Product Description(Electric Router)

The Electric Router gives you all of the functionality of a fixed router--and much more. Not only can it create decorative edging like a fixed router, but its unique construction allows you to start work in the middle of a piece of wood, rather than at the edge, which lets you create cut-outs, inlays, and more for stunning results. With its powerful 10 Amp, variable speed motor (6000 to 26,000 RPM), this electric router gives you superior power for maximum performance, and its gradual start function gives you optimum control over the tool for precise results and safety. The tool is also built for convenience, with a specially designed base that allows for improved visibility, an easy-to-use depth scale to ensure better accuracy, and a spindle lock for straightforward, simple bit changes. And with its trigger switch with lock-on button and its contoured chip shield, you'll be both more comfortable and safer while you perform your work. The router comes with a 1/4-inch collet and wrench and an adjustable parallel edge guide.

Advantage(Electric Router)

1.Equipped with an improved collet chuck for maximum hold and bits can be easily changed
2. Dust guide diverts dust and debris away from the work piece and user
3. Elastomer covers the handles to reduce transfer of vibration and prevent slippage
4. Soft start motor for reducing torque during start up
5. Variable speed dial is conveniently so the user can finely adjust the rotation speed without removing a hand or eyes from the work piece

Technical parameter(Electric Router)

Rating

230V~50Hz/120V~60Hz

Rated Input Power

1200W

No Load Speed

11000-30000rpm

Tool Holder

Φ6/8mm

Plunge Depth

Max.55mm

Weight

3.15kg

Packing Size

68x28x29.5cm/4pcs

Pcs/Container

1792pcs/20'

Speed setting

Clamping lever

Handle

Drilling extractor adapter

Union nut

ON/OFF switch

Collect 8 mm(preinstalled in union nut 3)

Start lockout

Locking screw

Extractor

Guide rail

Screw

Base plate

Collect 6 mm

Sliding plate

Rip fence

Step stop

Thrust ring

Spindle-lock key

Copy casing

Lock screw

Open-ended spanner with slot

Depth stop

Reducer

Index indicator

Sliding bar with screw for rip fence 24

Dial milling

Centering pin

Control dial(milling depth-fine adjustment)

 

Product Details(Electric Router)
12mm Double Handle Electric Router Electric Hand Wood Router
12mm Double Handle Electric Router Electric Hand Wood Router
12mm Double Handle Electric Router Electric Hand Wood Router
 

Operation of electric woodworking router(Electric Router)

Operation of electric woodworking router

Switching on and off

Switching on:

Press and hold the start lockout.

Activate the ON/OFF switch. Once the machine has started, release the start lockout.

Switching off:

Release the ON/OFF switch.

Presetting the speed

Set the desired speed using the speed setting wheel.

1-2=low speed

3-4=middle speed

5-7=high speed

Set the milling depth

1. Ensure that the clamping lever is locked down. If it is loose turn it anti-clockwise until it is locked.

2. Place the device on the work piece to be worked upon.

3. Turn the step stop until it locks into the lowest position.

4. Loose the lock screw.

5. Loose the clamping lever by turning it clockwise and pushing the device down until the route bit touches the surface of the work-piece.

6. Lock the clamping lever in place by turning it anti-clockwise.

7. Push the depth stop down until it reaches the lowest position of the step stop. Move the index indicator to the position "0" on the dial milling depth adjustment.

8. Adjust the depth stop to the desired depth, tighten the lock screw. After the index indicator should no longer be adjustable.

9. Loose the clamping lever and lead the device back up.

Readjust the Milling depth

The milling depth can be adjusted with the control dial.

Loose the clamping lever by turning it clockwise and pushing the device down until the depth stop touches the step stop.

Lock the clamping lever in place by turning it anti-clockwise.

Set the milling depth with the control dial.

Loose the clamping lever by turning it clockwise and lead the device back up. Check the milling depth through a further practical test.

Set the milling depth with the step stop

You can use the step stop will deeper depths in several steps with less takeoff.

Set the desired milling depth with the lowest step of the stop.

Then set it at higher level for the first attempt.

Milling direction

The milling process must always go against the rotationary direction on the router bit

When milling in the direction of the router bit (counter rotation) the device fly out of your hand.

Milling Process

Set the milling depth as previously described.

Place the device on the desired work-piece and switch it on.

Loose the champing lever by turning it clock-wise and pushing the device down until it touches the surface of the depth stop on the step stop.

Lock the device into place by turning the clamp lever anti-clockwise.

Mill with even speed and even pressure

Set the copy casing

Set the copy casing from below on the sliding bar.

Secure the copy casing with the two screws of the extractor adapter on the base plate

Milling with the copy casing

Always keep the device clean, dry and free of oil or grease.

Use a dry cloth to clean the housing.

Milling with a rip fence

Push the rip fence along the guide rail of the base plate and tighten the screws.

Put the rip fence on the edge of the work piece

Milling with a circular compass

Put the centring pin in the marked mid point of the circle.

Turn the rip fence over, i.e.the fence side is facing upwards.

Screw together the centre pin and the rip fence with a wing bolt. Lock the centre pin to the screws with the slot of the open-ended spanner.

Our Service(Electric Router)

a.1 year warranty
b.1%-2% Spare Parts
c. OEM & ODM are welcome
d. trial orders are available
e. Reply within 24 hours

our company(Electric Router)

BEIJING ZLRC Enviromental Protection Equipment Co., ltd mainly foucs on electric tools and export.Our main products include electric router,welder,band saw,angle grinder and other power tools.It already has with more 20 years in China.And there are good service and  warranty.
12mm Double Handle Electric Router Electric Hand Wood Router


Packaging & Shipping(Electric Router)

Every piece will be  packed in a small packing of  box or cartons which depend on the requirment.
12mm Double Handle Electric Router Electric Hand Wood Router

FAQ(Electric Router)

Q1:HOW LONG CAN I GET THE FEEDBACKS AFTER WE SENT THE INQUIRY?
We will reply you within 12 hours in working day.

 

Q2: ARE YOU A DIRECT MANUFACTURER OR TRADING COMPANY ?

We have our own factory and international sales department. We produce and sell all by ourselves.

 

Q3: WHAT'S THE PAYMENT TERM?

For mass production goods, you need to pay 30% deposit before production and 70% balance against copy of documents.

The most common way is by T/T. Paypal.

 

Q4:HOW TO GUARANTEE THE QUALITY AND AFTER-SALES SERVICE OF YOUR GOODS?

1,Strict detection during production.

2,Strict sampling inspection on products before shipment and intact product packaging are ensured.

3,Follow up and adopt customers' feedbacks in a timely manner after sales.


Q5:WHAT IS YOUR WARRANTY TERM?
Our company offer 1% free spare parts to FCL order.There is a 12months warranty for our export products from the date of the shipment.If warranty has run out,our customer should pay for the replacement parts.


Q6:CAN I USE MY OWN LOGO AND DESIGN ON PRODUCTS?
YES, OEM is welcomed.


Q7:HOW LONG IS THE DELIVERY TIME?
A:2-7 days for the sample order.
B:30-40 days for LCL or FCL order depend on order quantity.

 

Q8: CAN I CHECK THE QUALITY OF GOODS BEFORE DELIVERY?

A:Yes, you can come to our factory by yourself or ask colleagues from your Chinese office or even ask a third party inspection company to check the quality of goods before delivery.

B:We also can provide free professional inspection service and will send professional inspection report to you before shipping.


If you have another question, pls feel free to contact us as below:

BEIJINGZLRC ENVIRONMENTAL PROTECTION EQUIPMENT CO.,LTD
Add:VIP Eastern Courtyard ,Building 7 ,Hanwei International,Fengtai District,Beijing,China
Tel: 86-10-87587386
Fax:+86-10-67536885

 

The process and characteristics of honing steel tube and improving surface roughness can almost reach Ra less than 0.4 um. 2. Correct the roundness, the ellipticity can be less than 0.01 mm. 3, improve the surface hardness, eliminate the stress deformation, hardness HV 4 ° or higher



After processing, the residual stress layer shall improve the fatigue strength by 30%.


Improve the coordination quality, reduce wear and tear, and prolong the life of cylinder.

Internal diameter tolerance: H8, H9, straight line 0.3mm/ 1000mm, 0.5mm/ 1000mm.

Stainless Steel Honed Tube

Stainless Steel Honed Tube,Stainless Steel Honed Steel Tube,Cold Rolled Steel Tube,Stainless Honed Carbon Steel Tube

Yangzhou Yinhe Machinery Co., Ltd , http://www.yinhesteeltubes.com