Triaxial vibration sensor
A pressure vessel is a vessel that can withstand high pressures and is commonly used for storing, transporting, and processing various gases, liquids, and gaseous liquid mixtures. The pressure vessel is mainly composed of vessel body, flange, seal, support and accessories. Common pressure vessels are gas cylinder, gas storage tank, distillation tower, reactor and so on.
The design and manufacture of pressure vessels must comply with relevant national standards and specifications, and pass strict inspection and testing to ensure their safety and reliability. During use, you must comply with the operation regulations and safety precautions, and periodically check and maintain the device to ensure its normal operation and safe use.
The main business scope is various heaters, waste heat boilers, pressure vessels, supportingair preheaters, air coolers, furnace accessories and accessories, and provide equipment installation, with EPC ability of projects. At present, our customers have covered all large and medium-sized petrochemical enterprises in China and established long-term strategic cooperative partnership with them. Products are exported to Southeast Asia, Middle East, and other regions.
Pressure Vessel,Reactor Tanks Vessel,Reactor Equipment Sales,Stainless Steel Reaction Reactor Jiangsu Gelan Environmental Technology Co., LTD , https://www.glkj2010.com
It is an inertial sensor that uses a magnetoelectric induction principle to convert a vibration signal into a voltage signal that is proportional to the vibration velocity value. This sensor can be used to measure mechanical vibrations as low as 5 Hz.
1. The output signal is proportional to the vibration speed, which can balance the high-frequency, medium-frequency and low-frequency vibration measurement fields.
2. SZ-4 series sensors have lower output impedance and better signal to noise ratio. There are no special requirements for the output plug and cable, and it is easy to use.
3. The frictional moving element is eliminated in the sensor design, so it is flexible and can measure small vibration (0.01mm).
4, the sensor has a certain resistance to lateral vibration (not greater than 10g peak)
Three-axis vibration sensor technical parameters:
Sensitivity: 50mV/mm/s ± 5%;
Test conditions: (temperature 20 ° C ± 5 ° C, measured at 80 Hz, speed 10 mm / s)
Amplitude limit: ≤2000μm (peak-peak);
Frequency response: (4~1000) Hz;
Zui large acceleration: 10g;
Measuring direction: SZ? 4V (vertical type)
SZ? 4H (horizontal type)
Installation method: the center hole of the bottom of the sensor is fixed with an M10×1 screw;
Environmental conditions: dustproof, moisture proof
Operating temperature: (-30 ~ 120) °C;
Relative humidity: ≤95% (non-condensing);
Dimensions: Φ35 × 78 (mm3);
Weight: 300g.
SZ-6 type magnetoelectric speed sensor
SZ-6 (C) type magnetoelectric speed sensor
The SZ-6 magnetoelectric speed sensor is an inertial sensor that uses a magnetoelectric induction principle to convert a vibration signal into a voltage signal that is proportional to the vibration velocity value. It can be used to measure the vibration of the bearing housing, housing or structure (absolute vibration relative to the inertial space). It is directly installed outside the machine and is extremely easy to use and maintain.
Technical Parameters
Sensitivity: 50mV/mm/s ± 5%;
Test conditions: (temperature 20 ° C ± 5 ° C, measured at 80 Hz, speed 10 mm / s)
Amplitude limit: ≤2000μm (peak-peak);
Frequency response: (10~1000) Hz;
Zui large acceleration: 10g;
Measuring direction: vertical or horizontal; (universal) type SZ-6c
Installation method: the center hole of the bottom of the sensor is fixed with an M10×1 screw;
Output wiring method: SZ-6 type aviation connector;
SZ-6c type terminal block;
Environmental conditions: dustproof, moisture proof
Operating temperature: (-30 ~ 120) °C;
Relative humidity: ≤95% (non-condensing);
Dimensions: SZ-6: Φ35 × 78 (mm3);
SZ-6c: Φ29×51 (mm3);
Three-way vibration speed sensor
OD9004/S2162/S2112/VB-Z420/VB-Z430/VRS2000A11/VRS2000A1 dual channel vibration monitor instrument
HY-101/HY-102/HY-103/HY-103B/HY-103C/HY-103E/HY-104/HY-105/HY-106/HY-106C/HY-107/HY-107R/HY- 108/HY-109A vibration meter
VIBRA double channel tile vibration monitor instrument CZ-6/6SZ-6 fan magnetoelectric vibration speed sensor SZ-6Cc dual channel digital display vibration instrument
CZJ-B2/CZJ-B3/CZJ-B3G/CZJ-B4/CZJ-B4G/CZ-6/CJZ-D/CJZ-D2/MLI-2001/WB-9902/WB-8112B/ZJ2/ZJ2-A double Channel wall-mounted tile shock measuring instrument bearing vibration monitoring and protection instrument SZ-4 magnetic electric speed sensor
8500LD/85100XY/85564/85200/85850BCD-21A/VIBROCONTROL110/EN900/EN2000A1/Double-channel tile vibration monitor instrumentation
SZ-4 magnetoelectric speed sensor SG-2W, SG-02Y vibration sensor
CD-1/CD-2/CD-4/CD-4A/CD-6/CD-6A/CD-7-C/CD-7-S/CD-8/Double-channel tile cover vibration sensor
CD-21-2-C/CD-21-2-S/CD-21-T/CD-21-TA/CD-21C/S/BCD-21A/CD721/WIND Watt Vibration Velocity Sensor
MLS-9W/MLV/20/30/60/70/Axis vibration vibration sensor
MLV-9200(16699/900)/9200/74712/47633/HT-2ZD-24/ZD25/ZDF bearing vibration speed sensor ZXP-F3200/ZXP-J116/ZXP-J200/ZXP-J210/ZXP-J220/ DZX-400/PDM1201/WLI-2004/WLI-2003/WPDM1201/LI-2001/S2662/VRS2000A11/WLI-2011/PT2010/11 dual channel tile shock bearing vibration monitor instrument SG-2W, SG-02Y vibration sensor
ZXP-J400/ZXP—J510/ZXP—J520/XD-2/XZK-1/OD-9008S/Double-channel tile cover vibration meter measurement instrument