Hydraulic pump piston pump use and maintenance methods:

In this paper, the direct-axis swash plate piston pump mainly introduces the use and maintenance of hydraulic pump piston method.

1 hydraulic pump oil supply form

Straight shaft swash plate piston pump is divided into two types of self-suction oil pressure type. Most of the pressure supply type hydraulic pump with air pressure tank, there are hydraulic pump itself with a charge pump to the hydraulic pump inlet to provide pressure oil. Self-priming oil pump self-priming oil capacity, no external oil supply. Hydraulic pressure oil tank, each time you start the machine, you must wait for the hydraulic pressure tank to reach the use of pressure, to operate the machine. If the pressure of the hydraulic tank is low, it will cause the pull-off phenomenon in the hydraulic pump and the slippery whip, which will cause abnormal wear of the return plate and the pressure plate in the pump body. The use of charge pump piston pump, after use, the operator needs to check the plunger pump 1-2 times a day to check the hydraulic pump running sound is normal. If you find the hydraulic cylinder speed or boring car, you should disassemble the charge pump check, check the edge of the impeller scratches, internal gear pump clearance is too large. Self-sucking oil-type piston pump, the hydraulic oil tank fluid shall not be lower than the lower limit of oil, to maintain a sufficient amount of hydraulic oil. The higher the cleanliness of the hydraulic fluid, the longer the life of the hydraulic pump.

2 hydraulic pump bearings

Piston pump is the most important part of the bearing, if the bearing appears clearance, you can not guarantee the hydraulic pump within the three pairs of normal friction pair, but also destroy each friction pair hydrostatic bearing oil film thickness, reduce piston pump bearing Service life. According to information provided by the hydraulic pump manufacturer, bearing the average service life of 10000h, more than this value will need to replace the new port. Demolition of the bearings, there is no professional testing equipment can not detect the bearing clearance, can only be visually, if the surface of the roller scratches or discoloration, it must be replaced. In the replacement of bearings, bearings should pay attention to the original letters and models, most of the piston pump bearing load capacity of large bearings, it is best to buy the original manufacturer, the original specifications of the product, if the replacement of another brand, should consult the bearing experience Staff look-up table swap, the purpose is to maintain the bearing accuracy level and load capacity.

3 pairs of friction pair inspection and repair

3.1 Plunger rod and cylinder bore

Piston pump parts replacement standards, the various listed tolerances, can be repaired as follows:

(1) cylinder inlaid copper sleeve, copper sleeve can be replaced by the method of repair. First set a set of plunger rod diameter trim to a uniform size, and then over 1000 # polished sandpaper outside diameter. Cylinder installation copper sleeve of three ways: (a) cylinder warm or copper sleeve low temperature cryogenic extrusion, interference assembly; (b) mining with Loctite adhesive assembly, which method we require copper jacket Diameter surface of the groove; (c) cylinder tapping, copper outer diameter of the thread, Tu Le Ta plastic, screw into the assembly.

(2) The cylinder and the copper sleeve fused by means of sintering are as follows: (a) grind and repair the cylinder hole by using a grinding rod, manual or mechanical method; (b) re-boring the cylinder bore by using a coordinate boring machine; (c Reamer cylinder bore repair.

(3) adopt "surface engineering technology", the method is as follows: (a) electroplating technology: a layer of hard chrome plating on the plunger surface; (b) electroplating technology: brushing wear- Thermal spraying or arc spraying or electrospraying: spraying high-carbon martensite wear-resistant material; (d) laser welding: welding high hardness wear-resistant alloy powder on the plunger surface.

(4) Cylinder hole copper-free sleeve cylinder materials are mostly ductile iron, the cylinder wall to prepare amorphous film or coating. Because of this special material on the inner wall of the cylinder bore, it is possible to form a hard-hard paired friction pair. If you blindly grind the cylinder bore, the surface material inside the bore of the cylinder bore is removed and the more structural properties of the friction change. Was removed coating friction pair, if forced to use, the friction surface temperature will rise sharply, the plunger rod and cylinder bore gluing.

In addition to the surface of the plunger rod to prepare a unique film coating, the coating contains anti-wear + wear + lubrication function, this group of friction actually hard or soft match, once people change the coating, it will destroy the most Good matching pair of friction materials, repair these special plunger pump, it is necessary to send a professional repair shop.

3.2 Slippers and swash plate

Sliding friction between slipper and swashplate is the most complex pair of three pairs of swashplate piston pump. Table 1 shows the clearance between the plunger rod and the ball socket (see Figure 2). If the gap between the plunger and the shoe is out of tolerance, the high pressure oil in the plunger chamber will leak from the clearance between the ball head and the shoe In the leakage, slippery shoes and swash plate thinning, severe hydrostatic pressure caused by failure of the support, slipper and swash plate metal contact friction, slipper ablation off, plunger ball head scratched swashplate. Plunger rod ball head and sliding ball socket beyond the tolerance 1.5 times, it must be replaced in groups. Plunger rod and cylinder bore Plunger rod diameter φ16φ20φ25φ30φ35φ40 Standard clearance 0.0150.0250.0250.0300.0350.040 Limit clearance 0.0400.0500.0600.0700.0800.090 Standard clearance 0.0100.0100.0150.0150.0200.020 Piston rod Ball head and sliding ball socket Ultimate clearance 0.300.300.300.350.350.35 swashplate effect After a period of time, the swashplate surface will appear concave phenomenon, before using the platform grinding, we should first measure the original size and plane hardness. Grinding, and then measure the amount of grinding is, such as within 0.18 plunger pump use without interference; if more than 0.2mm above, you should use nitriding method to maintain the thickness of the original nitride layer.

When the swash plate plane is scraped out of the groove by the plunger ball head, the method of laser alloy powder can be used for repairing. Laser cladding technology can not only ensure the bonding strength of the material, but also ensure the hardness of the filler material, and does not reduce the hardness of the surrounding tissue.

Also Shun to adopt chromium welding rod for manual surfacing, welding of the swash plate plane to be re-heat treatment, the best nitriding furnace heat treatment. Regardless of the method used to repair the swashplate, you must restore the original dimensional accuracy, hardness and surface roughness.

3.3 with the flow plate and cylinder with flow surface repair

With a flat plate with a flat surface with the flow of two forms. Spherical with the flow of friction pair, the cylinder with flow surface scratches relatively shallow, by means of grinding repair; cylinder with flow grooves deep, should first use "surface engineering" means to fill the trench, and then grinding , Can not be blind grinding, to prevent copper thinning or leakage of steel base. Friction pair in the form of plane flow can be grinded on the platform with high accuracy.

Before the grinding of the cylinder body and the valve plate, the total thickness dimension and the size that should be ground off should be measured before compensation to the adjusting mat. With a larger flow plate, the grinding should be re-heat treatment to ensure that hardened layer hardness. Piston pump parts hardness Standard plunger rod Recommended hardware hs84 plunger rod ball head Recommended hardness> hs90 Recommended surface hardness of swashplate> hs90 Recommended hardness of shunt plate> hs90 After the cylinder block and plate repair, the following methods can be used to check the mating surface Of the leakage, that is, in the distribution plate coated with Vaseline oil, the drainage block blocked, painted with oil flow plate flat on the platform or flat glass, and then put the cylinder on the plate with a hole in the cylinder into the diesel , To interval oiling, that is, a hole oiling, a hole without oil, observe 4h above, no leakage and collusion of diesel in the plunger hole, indicating that the cylinder body and with the flow plate grinding qualified.

4 Conclusion

Piston pump life, with the usual maintenance, the number and quality of hydraulic oil, oil cleanliness and so on. Avoid oil particles in the piston pump friction caused by wear and tear, but also to extend the effective life of the plunger pump. In the maintenance of replacement parts should try to use the original production of parts, these parts sometimes fake parts than other expensive, but the quality and stability is better, if the purchase of counterfeit parts cheaper prices in the short term seems to be saving costs, However, this poses a hidden danger, may also cause greater damage to the use of the plunger pump.

More Search Keywords: Pumps

Gasoline Car

As a traditional means of transportation, gasoline vehicles have always played an important role in people's lives. It not only meets people's travel needs, but also has a positive impact on social and economic development.

The history of gasoline cars can be traced back to the late 19th and early 20th centuries. Since Carl Benz invented the first car in the world in 1886, the research, development and production of gasoline vehicles have gradually become the focus of attention. With the continuous development of technology, gasoline vehicles have gradually replaced steam cars and electric vehicles as the mainstream means of transportation. Gasoline vehicles are loved by consumers due to their high speed, long range, and convenient refueling.

Gasoline Car,Used Car,Mpv Car,Trunk Car

Chongqing Huanyu Automobile Sales Company , https://www.nbhuanyuauto.com